Updated Nov 17, 2026· 5 min read

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

Testing a cordless tool charger is useful when a battery will not charge, the charger light behaves oddly, or you are checking a used charger before buying a replacement battery. The safe goal is to measure voltage and observe charging behavior—not to make the charger deliver power into an unknown load.

Before You Test

Identify the battery platform and charger type first. Most modern tool batteries use lithium-ion cells and have extra terminals for temperature sensing, cell monitoring, or communication. The main positive and negative terminals may not produce a useful output until the charger detects a battery. Some chargers also pulse their output, so a quick voltage reading can be misleading.

Remove the battery from the charger before inspecting it. Look for cracked plastic, burnt terminals, melted insulation, corrosion, or a loose power cord. Do not test a battery that is swollen, leaking, hot, or physically crushed. Place a questionable lithium-ion battery in a nonflammable area and follow the manufacturer’s recycling or hazardous-waste instructions.

You will need a digital multimeter with insulated probes. A basic meter is sufficient; an expensive bench meter is not required. Use a small flashlight and, if needed, a plug-in outlet tester to confirm that the wall outlet is wired and powered correctly. A digital multimeter with an auto-ranging voltage setting is the easiest option for occasional troubleshooting.

Understand the Voltage You Should See

Tool battery labels usually show a nominal voltage, not the charger’s final voltage. A “18V” or “20V Max” lithium-ion pack commonly charges to about 20–21 volts. A 12V Max pack often reaches about 12.6 volts, while a 24V-class pack may charge to roughly 29.4 volts. These are general figures, not universal specifications.

Battery label Typical lithium-ion pack Approximate full-charge voltage
12V Max 3 cells in series 12.6V
18V or 20V Max 5 cells in series 21.0V
24V or 25.2V 6 cells in series 25.2V
36V or 40V Max 10 cells in series 42.0V

Do not compare the charger’s output with the number printed on the battery alone. A charger for a five-cell pack may show around 21 volts with the battery removed, and that can be normal. The charger must also control current, monitor temperature, and stop at the correct voltage.

Measure Voltage Without a Battery

Set the meter to DC voltage. If it is not auto-ranging, select a range higher than the charger’s expected output—such as 50V DC for an 18V platform. Plug the charger into a known-good outlet, but do not insert a battery.

Touch the black probe to the charger’s negative contact and the red probe to the positive contact. Keep the probe tips separated. Do not bridge adjacent terminals with a screwdriver, test lead, or metal ruler. Record the reading after a few seconds, then watch it for about 30 seconds.

Some chargers show little or no voltage with no battery connected. That does not automatically mean they are defective. Electronic chargers may keep their output disabled until they detect the correct battery, temperature sensor, or communication signal. Other chargers show a voltage near the pack’s maximum charging voltage.

A negative reading usually means the probes are reversed, not that the charger is damaged. A reading that is dramatically higher than the expected full-charge voltage is a reason to stop using the charger. For example, roughly 30 volts from a charger intended for a five-cell 18V/20V Max pack indicates a serious fault or a mistaken charger identification.

Test Charging With a Compatible Battery

The most meaningful test uses a known-good, correctly matched battery. Never insert a pack just because it physically fits. Some brands have similar rails but different electronics, and adapters can defeat temperature or communication protections. Use the charger specified for that battery platform.

Check the battery’s starting voltage before charging. A five-cell pack reading around 15–20 volts may simply be partly discharged. A reading near zero, a rapidly changing reading, or a pack that is hot suggests a battery-side problem. Do not attempt to “wake up” a deeply discharged lithium-ion pack with a bench supply or another battery.

Insert the battery and observe the charger indicator. A normal charger should begin a charging sequence, often showing a steady or flashing light, then change state when charging is complete. Measure only at accessible battery terminals if the design allows it without slipping probes into the charger. Do not probe internal cell connections or puncture insulation.

During charging, the battery and charger may become mildly warm. Stop if either becomes too hot to comfortably touch, smells sweet or burnt, swells, clicks repeatedly, or shows an error. A charger that runs its cooling fan and gradually changes indicator status may be working normally even if its open-circuit voltage reading was unusual.

Do Not Test Current the Wrong Way

The most common multimeter mistake is selecting amps and placing the probes across the charger’s positive and negative terminals. In current mode, the meter is nearly a short circuit. This can blow the meter fuse, damage the charger, arc the contacts, or trip the battery’s protection system.

Do not connect a resistor, automotive bulb, heating element, or improvised load to simulate a battery unless you understand the charger’s control circuit and the load’s power rating. A 21V charger delivering only 2 amps produces 42 watts, enough to overheat small resistors and wiring quickly. A load test also cannot verify the charger’s battery communication functions.

When Replacement Makes Sense

Replace or professionally service the charger if it has a damaged case, exposed wiring, a burnt smell, repeated fault codes with multiple known-good batteries, or an output that is far outside the platform’s expected range. Do not open a mains-powered charger unless you are qualified; capacitors can retain dangerous voltage after unplugging.

For a replacement, the cheapest sensible choice is usually a genuine charger made for the exact battery platform. A platform-compatible replacement charger can be fine when it lists the correct voltage, battery series, and safety certifications. Avoid universal chargers that rely on bare contacts or vague claims such as “fits all 18V batteries.”

If you maintain several packs, a dual-port charger may save time, but it does not charge two packs twice as fast unless the manufacturer specifically says it does. For one or two batteries, the standard single-pack charger is usually cheaper, simpler, and adequate.

L
Loa Power Tools Editorial Team
We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.

Related guides

Browse all Best Of guides →

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.