Updated Nov 11, 2026· 10 min read

Our Top Picks

  1. Echo 330095071 String Trimmer Line
    Check on Amazon
  2. Traverse Creek Incorporated Genuine Echo Black Diamond LINE
    Check on Amazon
  3. Trimmer Line
    Check on Amazon

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

How to restring a string trimmer depends on one thing before anything else: the type of head on the end of your shaft. Some heads wind new line in through the eyelets in under a minute, some need to be opened and loaded by hand, and a few simply take cut pieces of line. Identify the head first, then use the matching steps below for Ryobi, EGO, Stihl, Echo or Milwaukee. This guide is organised around head type, so you can go straight to the section that matches the trimmer in your hand. Always take out the battery or pull the spark plug boot before you touch the head, and check your manual for line size and length.

Key takeaways

  • Four head families cover nearly every trimmer: manual bump-feed spools, wind-in easy-load heads, fixed-line heads and pre-wound cartridges.
  • Easy-load heads (EGO POWERLOAD, Ryobi Reel Easy+, Milwaukee, Stihl AutoCut EasySpool, Echo Speed-Feed) are loaded through the eyelets with equal ends, then wound.
  • Line diameter is set by the head, not by what is on the shelf; .095 inch is common, .080 inch on some lighter heads. Never go thicker than the manual allows.
  • Overfilling is the most common reason a freshly loaded head will not feed. Use the length your manual specifies.
  • A 3-pound bulk spool costs less per reload than pre-cut packs, and it gives you dozens of fills.

Step Zero: Which String Trimmer Head Do You Have?

Switch the trimmer off, remove the battery or the spark plug boot, and look at the head. This table lets you match what you see to the loading method.

How to restring a string trimmer: match your head type to the loading method
Head type How to recognize it Examples Loading method Opens up?
Wind-in, button or crank Eyelets on the side, a button or crank on the head EGO POWERLOAD, Ryobi Reel Easy+ with Speed Winder Push line through, then press the button or turn the crank No
Wind-in, turn the head Arrows on the head and outer ring, line eyelets Milwaukee M18 FUEL, Stihl AutoCut C 26-2 EasySpool, Echo Speed-Feed 400 Align arrows, push line through, rotate the head or spool No
Manual bump-feed spool A cap you push or twist off, a spool inside Older Ryobi, Homelite, Craftsman and universal heads Open the cap, wind the line onto the spool by hand Yes
Fixed-line head Holes in the head and no spool Pivoting and four-way universal heads Cut pieces and thread each one in Sometimes
Pre-wound cartridge A clip-on plastic spool already loaded with line Maker refill spools Replace the whole spool Yes

How to Replace Trimmer Line: The Universal Steps

These steps work on any head, with brand-specific differences in the sections that follow.

  1. Power down. Remove the battery or unplug the cord; on a gas trimmer, pull the plug boot. A cut-off blade can start without warning when the trigger is pressed.
  2. Clear the head. Pull out any leftover line and brush away grass, wire and dirt packed around the eyelets.
  3. Pick the right line. Use the diameter in your manual. Round line is quiet and economical; twisted and shaped lines cut grass and reduce noise but can be less suited to some heads.
  4. Measure the length. Cut the amount specified in the manual. If you cannot find it, the range on common heads is about 13 to 26 feet depending on diameter and head size. More line is not better: it overfills the spool.
  5. Load the line. Follow the head’s method: thread through the eyelets and wind, or wrap by hand around a spool.
  6. Leave working ends. Pull the ends out until about 5 to 7 inches stick out each side and fit them into the notches, so they do not tangle.
  7. Refit and check. Reassemble the head, check the line moves freely when you tug the ends, and reinstall the battery.

How to Restring a Ryobi Trimmer

Many Ryobi trimmers use the Reel Easy+ bump-feed head with a Speed Winder crank. According to Ryobi’s product page, you insert the line and push it through until the length is equal on both sides, then turn the Speed Winder crank clockwise until about 6 inches of line is left on each side. The page lists .080-inch and .095-inch line as compatible, and says the head fits Ryobi, Toro and Homelite bump-feed trimmers.

For older Ryobi bump-feed heads without the crank, open the cap, thread the line through the spool’s center hole, wind it neatly in the direction marked by the arrow on the spool, and feed the ends out through the eyelets before you close the cap.

How to Remove a Trimmer Head on a Ryobi

If you need to swap the whole head, remove the battery first. Locate the small hole in the drive-shaft housing, insert a hex key or screwdriver to lock the shaft, then turn the head. Many trimmer heads are threaded in the reverse direction, so the head may come off by turning it clockwise on a straight-shaft model, but this varies. Check your manual or the arrow on the head before you apply force.

How to Restring an EGO Trimmer

EGO’s POWERLOAD head winds line without opening the housing. The steps shown in EGO-owner guides are: take out the battery, pull out any leftover line, and push the new line straight through the head. Put the battery back in and press the POWERLOAD button, and the head winds the line onto the spool. If your model asks you to rotate the head until the two arrows click into alignment, do that first. The common line is .095 inch, with .080 inch listed on some models, and about 13 to 16 feet is the usual quantity, but follow the manual for your model.

The older standard EGO head is a bump-feed spool that you open and wind by hand, like the manual Ryobi head above.

How to String an Echo Trimmer

Echo’s Speed-Feed 400 head is a common fitment on Echo gas trimmers and is also sold as a universal replacement for other brands. You load it without taking it apart: line goes through the eyelets, you pull it until both sides are equal, and you wind with the knob or cap. Owners report that the universal-fit Speed-Feed 400 is used with .095-inch line, so check the diameter stamped on your head before you buy line. Stop when the ends are 5 to 7 inches long.

How to Restring a Stihl Trimmer

The Stihl AutoCut C 26-2 with EasySpool is loaded without disassembly. Stihl’s New Zealand guidance describes this sequence: align the grooved line on the head with the arrows on the outer ring, push one end of the line into the eyelet until it comes out the other side, pull the line halfway through so both sides are equal, then turn the spool in the direction of the arrows to wind the line in. Stop when the ends are close to the line limiter and trim any excess. The listing states .095-inch (2.4 mm) line with up to 8 meters (about 26 feet) of line, with .105 inch as an optional size. Fill to the amount in your manual; sources differ, from about 14 feet up to the maximum.

How to Load a Milwaukee String Trimmer

Milwaukee M18 FUEL trimmers use an Easy Load style head. The steps in the operator’s manual start by removing the battery and clearing grass and debris from the head. Align the head indicators with the eyelets, feed the line through until both sides are equal, then rotate the head to wind until about 5 to 6 inches stick out on each side. The manual lists 2.0 mm (.080 inch) and 2.4 mm (.095 inch) as the best sizes and says to use Milwaukee line. For .095 line, the manual’s figure is about 20 feet (6.1 meters). The head also supports thicker line, but treat that as a case-by-case check against your manual.

Line Length and Diameter by Head

Line diameter and length for the heads in this guide, from manuals and maker pages
Head Common diameter Typical length per load Wind method
Ryobi Reel Easy+ .080 or .095 inch Until about 6 in. is left each side Crank, clockwise
EGO POWERLOAD .095 inch (some .080) About 13 to 16 ft, or per manual Press the button
Stihl AutoCut C 26-2 .095 inch (.105 optional) Up to about 26 ft; check manual Turn the spool with the arrows
Echo Speed-Feed 400 .095 inch (check head) Per manual Turn the knob or cap
Milwaukee M18 FUEL .080 or .095 inch About 20 ft of .095 line Rotate the head

Worked Example: How Many Reloads in a Bulk Spool

Listings for 3-pound bulk spools of .095-inch line run from about 750 feet to just over 1,000 feet. At a 20-foot fill, a 750-foot spool gives roughly 37 reloads, and a 1,000-foot spool about 50. A 250-foot stick of branded line at the same fill gives about 12 reloads. If you reload once a month in season, a bulk spool lasts several years, and the cost per reload is a fraction of pre-cut packs. Store the line out of direct sun in a sealed bag, because dry, brittle line breaks sooner.

Why the New Line Will Not Feed

  • Overfilled spool. The coils crush against the housing. Unwind, trim to the specified length and reload neatly.
  • Crossed or twisted coils. Lines must lie side by side, not cross. Rewind in the arrow direction.
  • Wrong diameter. A line too thick jams in the eyelets. Match the head’s rating.
  • Melted or fused line. Heat from the work can weld the coils together. Replace the line; some owners soak line in water for a day before loading to keep it flexible.
  • Ends too short. If the ends are shorter than the limiter blade, the head cannot pull more out. Pull out 5 to 7 inches by hand.

Gear That Helps

  • Oregon Magnum Gatorline .095-inch x 282 feet: a twisted heavy-duty line suited to .095 heads on gas trimmers.
  • Milwaukee 49-16-2712 Trimmer Line: the maker’s own line, which matches the manual’s advice for M18 FUEL trimmers.
  • Reel Easy+ bump-feed head (part 314608005): a replacement head sold for Ryobi straight-shaft models such as RY15526, RY15527 and RY15529, useful if the old head is cracked.

Frequently Asked Questions

How do I replace trimmer line on any string trimmer?

Remove the battery or plug boot, clear the head, cut the line to the length in your manual and load it by the head’s method. Leave 5 to 7 inches out each side and check it feeds before you start.

How do I restring a Ryobi trimmer with the Reel Easy+ head?

Push the line through until both sides are equal, then turn the Speed Winder crank clockwise until about 6 inches remain on each side.

How do I restring an EGO trimmer?

Remove the battery, push the line straight through the POWERLOAD head, reinsert the battery and press the button. The head winds the line.

How do I string an Echo trimmer?

Thread the line through the Speed-Feed head’s eyelets, pull both sides equal and wind it with the knob or cap. Check the head’s diameter rating before choosing line.

How do I load a Stihl AutoCut C 26-2?

Align the grooved line with the arrows on the outer ring, push through the eyelet, even the sides and turn the spool in the arrow direction until the ends are near the limiter.

Can I use thicker line for more power?

No. Use the diameter in the manual. Thicker line overloads small motors, jams in eyelets and drains a battery faster.

How long should the line ends be?

About 5 to 7 inches on each side is a good starting point. If the ends are too short the head will not feed, and if they are too long the trimmer line cutter blade trims them back as you run.

Sources: Ryobi product page for the Reel Easy+ head; Milwaukee M18 FUEL operator’s manual; Stihl AutoCut C 26-2 maker guidance; EGO POWERLOAD guidance; bulk-line product listings. Check your own model’s manual for line size and length.

Last updated: November 2026

L
Loa Power Tools Editorial Team
We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
How to Restring a String Trimmer: Identify Your…Check price on Amazon

Related guides

Browse all Outdoor Power Equipment guides →

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.