Updated Nov 20, 2026· 8 min read

Key takeaways

  • Compare five bench grinders for sharpening chisels, plane irons and drill bits plus metal removal, from a compact 6-inch model to heavy 8-inch machines.

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

⭐ Key Takeaways
Quick answer: Our top pick is WEN 4276 6-Inch Bench Grinder with Flexible Work Light, with Metabo DS 150 6-Inch Bench Grinder as a strong alternative.

A bench grinder earns its bench space when it does two jobs well: putting a clean edge back on hand tools and removing metal fast when a part needs shaping. The wrong machine either burns the edge off a chisel or bogs down the moment it meets a mower blade. Wheel size, wheel speed and motor power decide which side of that line a grinder falls on, and the five machines below cover the full range.

This guide compares a compact 6-inch grinder, a slow-speed 8-inch sharpener, a dual-speed machine that does both jobs, and two heavy 8-inch workhorses. Each one is a different answer to the same question: how much grinding do you actually do, and how hot can the edge get before it suffers.

As an Amazon Associate, we earn from qualifying purchases.

Quick answer

For most home shops, the DEWALT DW758 is the safe all-round pick: a 3/4 HP motor, 3,600 RPM and 8-inch wheels handle sharpening and heavy metal removal alike. Sharpening-first shops should look at the slow-speed RIKON 80-805 at 1,750 RPM instead, while the BUCKTOOL TDS-200DS covers both jobs with two speeds in one machine.

The 5 best bench grinders

WEN 4276 6-Inch Bench Grinder with Flexible Work Light

WEN 4276 6-Inch Bench Grinder with Flexible Work Light

WEN 4276 6-Inch Bench Grinder with Flexible Work Light

Check price on Amazon

The WEN 4276 is the smallest and lightest grinder here, and that is its appeal. A 2.1-amp motor turns 6-inch wheels at 3,450 RPM, which is fast enough for sharpening lawn mower blades, axes, chisels and drill bits, and for cleaning rust off small parts. The flexible work light reaches over the wheels so the edge stays visible without a separate lamp on the bench.

At 16 lb it lifts off the bench and onto a shelf when the job is done, which matters in a crowded garage. The trade-off for the compact size is wheel width: 3/4-inch wheels wear a groove sooner than the 1-inch wheels on the 8-inch machines, and the 2.1-amp motor is a light-duty unit that suits short sessions rather than all-day grinding.

Specs: 2.1-amp motor; 3,450 RPM; 6 x 3/4 in wheels, 36-grit and 60-grit; 1/2 in arbor; flexible work light; 16 lb; 2-year warranty

Metabo DS 150 6-Inch Bench Grinder

Metabo DS 150 6-Inch Bench Grinder

Metabo DS 150 6-Inch Bench Grinder

Check price on Amazon

The Metabo DS 150 is the quiet professional in this group. Its maintenance-free induction motor runs with low noise and low vibration, and vibration-dampening rubber feet keep it planted on the bench. Two vitrified aluminum oxide wheels come in the box, a coarse 36-grit wheel for shaping and a fine 60-grit wheel for finishing an edge.

The 6-inch wheels and 150 mm format suit a shop where the grinder sharpens and deburrs rather than hogging off large amounts of steel. Spark guards and adjustable work rests are included, and the tool rest adjusts without extra tools. One thing to confirm on the listing before ordering: the maker manual for the DS 150 family lists 2,980 RPM on 50 Hz mains, while the US 60 Hz figure is not printed in the listing data checked here, so the speed figure is listed as not stated below.

Specs: 6 in wheels, 150 x 20 mm, 20 mm bore; 36-grit and 60-grit vitrified aluminum oxide wheels; maintenance-free induction motor; speed not stated; vibration-dampening rubber feet; 14.6 x 10.1 x 9.5 in; 21 lb

RIKON 80-805 8-Inch Low Speed Bench Grinder

RIKON 80-805 8-Inch Low Speed Bench Grinder

RIKON 80-805 8-Inch Low Speed Bench Grinder

Check price on Amazon

The RIKON 80-805 is built around one idea: a slower wheel keeps the edge cool. Its 1/2 HP motor turns 8-inch wheels at 1,750 RPM, roughly half the speed of a standard grinder, so a chisel, plane iron or turning tool spends less time with friction heat building in the steel. The two white aluminum oxide wheels come in 60 grit for shaping and 120 grit for refining, which is finer than the coarse pair most grinders ship with.

RIKON includes the accessories a sharpening station needs: a diamond wheel dresser to keep the wheel face flat and true, and a groove in the left tool rest for sharpening drill bits. The cast iron base sits on anti-vibration rubber feet, and a 5-year warranty is the longest coverage in this group. The slow speed is also the limitation: reshaping a chipped edge or removing heavy rust takes longer than it would on a fast machine.

Specs: 1/2 HP motor, 120V, 3A; 1,750 RPM; 8 x 1 in wheels, 60-grit and 120-grit white aluminum oxide; 5/8 in arbor; cast iron base; diamond dresser included; 6 ft cord; 34.2 lb; 16.38 x 10.75 x 11.25 in; 5-year warranty

BUCKTOOL TDS-200DS 8-Inch Dual Speed Bench Grinder

BUCKTOOL TDS-200DS 8-Inch Dual Speed Bench Grinder

BUCKTOOL TDS-200DS 8-Inch Dual Speed Bench Grinder

Check price on Amazon

The BUCKTOOL TDS-200DS answers the speed question by offering both speeds. A switch toggles its 1/2 HP induction motor between 1,725 RPM for sharpening edges without burning them and 3,450 RPM for fast deburring and rust removal, so one bolted-down machine covers the two jobs that usually need two grinders. The 8-inch white aluminum oxide wheels come in 80 grit and 120 grit, and a buffing wheel is included for polishing metal on the same machine.

The cast iron base has mounting holes, and BUCKTOOL builds it to be bolted down. At 45 lb it is the heaviest machine in this group after the DEWALT, and it takes up more bench depth than a 6-inch grinder. The cast aluminum tool rests adjust as the wheels wear, and a precision-machined flange keeps the wheels running true.

Specs: 1/2 HP dual-speed induction motor; 1,725 and 3,450 RPM; 8 x 1 in wheels, 80-grit and 120-grit white aluminum oxide; 5/8 in shaft; cast iron base with mounting holes; buffing wheel included; 45 lb; 16.9 x 10.6 x 16.5 in

DEWALT DW758 8-Inch Bench Grinder

DEWALT DW758 8-Inch Bench Grinder

DEWALT DW758 8-Inch Bench Grinder

Check price on Amazon

The DEWALT DW758 is the workhorse pick. A 3/4 HP induction motor drives 8-inch wheels at 3,600 RPM, and the 12.5-inch span between the wheels leaves room for long blades and wide workpieces that would foul a narrower machine. The rugged cast iron base and motor housing give it a solid feel on the bench, and the fixed high speed favors material removal over slow sharpening work.

This is the grinder to buy when the bench sees regular deburring, shaping steel and cleaning rusty parts. The single speed is the limitation: thin chisel edges heat up fast at 3,600 RPM, so edge work needs a light touch and frequent dips in water. Wheel grits are not stated in the listing data checked here, so confirm the included grits on the listing before ordering.

Specs: 3/4 HP induction motor; 3,600 RPM; 8 x 1 in wheels; 12.5 in between wheels; cast iron base and motor housing; wheel grits not stated; 17.75 x 12.63 x 11.73 in; 40 lb

How to choose

Wheel size comes first. Six-inch grinders suit small benches and light sharpening, while 8-inch wheels give a flatter contact patch for wide chisels and plane irons, last longer before they wear a groove, and accept the widest range of replacement wheels. If the grinder will sharpen more than it shapes, an 8-inch wheel is the better buy.

Speed comes second. Standard grinders run near 3,450 to 3,600 RPM and remove metal fast. Slow-speed grinders run near 1,750 RPM and keep heat out of a thin edge, which is what woodworkers and turners need. A dual-speed machine like the BUCKTOOL covers both jobs, while a variable-speed dial does the same with finer control.

Motor power comes third. A 1/2 HP motor holds speed through normal sharpening, while a 3/4 HP motor keeps turning when a heavy part presses hard against the wheel. Check the base too: a heavy cast iron base with mounting holes resists walking across the bench, and adjustable tool rests that lock at an angle make repeatable bevels possible. Finally, look at wheel width. Standard 1-inch wheels suit general work, while a 1-1/2-inch wheel accepts a CBN wheel later if sharpening becomes a serious habit.

Who should skip

Anyone who only touches up a kitchen knife now and then should skip a bench grinder entirely. A hand stone or a guided sharpener does that job with less noise, less dust and no bench space taken. A bench grinder also makes little sense on a bench with no room to bolt it down, since an unbolted grinder walks and vibrates.

Shops that grind aluminum or other soft metals should look elsewhere too, because soft metal loads up a grinding wheel and the wheel then cuts poorly and runs hot. Wet-wheel sharpening systems suit carvers who need the coolest possible edge and a water bath built in. And if the only grinding needed is a quick deburr on a small part, a hand file does the job without the setup, the dust or the noise.

FAQ

What size bench grinder should I buy for sharpening chisels?

An 8-inch grinder is the better pick for chisels and plane irons. The larger wheel gives a flatter contact patch, which keeps a wide edge square, and it runs cooler at the rim than a 6-inch wheel at the same RPM. A 6-inch grinder works, but its narrower wheels wear a groove sooner.

Is a slow-speed grinder better than a standard-speed grinder?

For sharpening, yes. A slow-speed grinder near 1,750 RPM puts about half the friction heat into the edge of a standard 3,600 RPM machine, so a chisel keeps its temper and its hardness. For fast metal removal, shaping and rust cleanup, the standard speed is better because it cuts faster.

Can I put a wire wheel on a bench grinder?

Yes, as long as the wire wheel matches the grinder arbor size and its maximum RPM rating clears the grinder speed with room to spare. A crimped wire wheel cleans rust and paint off metal quickly. Wear eye protection and a face shield, since wire wheels shed bristles.

Do bench grinders need to be bolted down?

Most 8-inch grinders should be bolted down, and several ship with mounting holes in the base for exactly that. Bolting stops the machine walking across the bench under vibration and keeps the tool rest gap steady. A light 6-inch grinder can sit loose for occasional use, but it still vibrates more than a bolted machine.

Final verdict

Buy the DEWALT DW758 if the bench does general shop work and the grinder needs to remove metal fast without complaint. Buy the RIKON 80-805 if sharpening chisels, plane irons and turning tools is the main job and a cool edge matters more than speed. Buy the BUCKTOOL TDS-200DS if one machine must do both jobs and the bench has room to bolt it down. The WEN 4276 suits a small bench and light duty, while the Metabo DS 150 suits a shop that values quiet, low-vibration running over raw power.

L
Loa Power Tools Editorial Team
We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Bench Grinders for Sharpening and Grinding WorkCheck price on Amazon

Related guides

Browse all Product Guides guides →

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.