Updated Nov 20, 2026· 9 min read

Key takeaways

  • Five layout squares compared for framing and roofing, from a compact 7-inch classic to a long 12-inch reach, with the scales and markings that matter.

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

⭐ Key Takeaways
Quick answer: Our top pick is IRWIN 1794464 Aluminum Rafter Square, 7-Inch, with Swanson S0101 Speed Square, 7-Inch as a strong alternative.

A speed square is the triangular layout tool that lives in a carpenter’s pouch from the first cut of the day to the last. In one compact body it combines a try square, a miter square, a protractor, and a rafter layout table, so it marks square and 45-degree lines, sets saw angles, and lays out rafters without a second tool. The best ones are machined flat, marked so the numbers stay readable in bright sun, and tough enough to survive drops onto concrete.

We compared five squares that cover the full range of framing and roofing work, from a compact 7-inch everyday carry to a 12-inch square for wide boards and long layout lines. Every pick below is an aluminum body with published rafter scales, and each one earns its place for a different reason: the lowest tier for a first square, the classic that set the pattern, the easiest markings to read, a magnetic heel for steel work, and the long reach of a 12-inch body.

As an Amazon Associate, we earn from qualifying purchases.

Quick answer

For most framing and roofing work, the Swanson S0101 7-inch square is the benchmark, with full rafter scales and a guide book included. If readability matters most, the Empire e2994 has the clearest laser-etched markings. For wide boards and long layout lines, the Swanson Big 12 adds five extra inches of reach. The IRWIN 1794464 is the sensible first square, and the magnetic Johnson Johnny Square holds fast on steel.

The Five Squares

IRWIN 1794464 Aluminum Rafter Square, 7-Inch

IRWIN 1794464 Aluminum Rafter Square, 7-Inch

IRWIN 1794464 Aluminum Rafter Square, 7-Inch

Check price on Amazon

The IRWIN 1794464 is the straightforward choice for a first speed square. It is a 7-inch aluminum body with permanent deep markings, built to do the core jobs: mark square and 45-degree lines, lay out rafter cuts, work as a protractor, and guide a circular saw along a straight edge. It covers the layout tasks a framer reaches for dozens of times a day without asking the buyer to learn a new system of scales.

The body is rustproof aluminum, so it shrugs off rain on a roof deck and damp lumber in a yard. The markings are cut deep into the metal rather than printed on the surface, which keeps the numbers legible after seasons of sliding across rough-sawn boards. IRWIN ships a rafter square reference guide with the tool, which walks through common rafter, hip rafter, valley rafter, and jack rafter layout for anyone who has not memorized the tables yet.

Specs
– Size: 7 in
– Material: aluminum, rustproof body
– Markings: permanent deep markings
– Scales: common rafter, hip rafter, valley rafter, jack rafter
– Functions: protractor, saw guide, tri square, miter square
– Reference guide: rafter square reference guide included
– Weight: not stated
– Dimensions: not stated

Swanson S0101 Speed Square, 7-Inch

Swanson S0101 Speed Square, 7-Inch

Swanson S0101 Speed Square, 7-Inch

Check price on Amazon

The Swanson S0101 is the original speed square, and it remains the pattern every other square is measured against. Swanson invented the tool, and the 7-inch S0101 has been made in the USA for decades. The body is heavy-gauge die-cast aluminum with a matte finish that cuts glare on a sunny roof deck, and the corners are CNC machined to 45 and 90 degrees, which is what the accuracy of every mark depends on.

A pivot point and degree scale handle angle marking from 0 to 90 degrees, common rafter and hip and valley rafter scales cover roof layout, and quarter-inch scribe notches mark rip lines parallel to a board edge. The 7/8-inch heel holds the square firmly against a board edge for square and 45-degree marks and for guiding a circular saw. A 62-page Blue Book of rafter lengths and roof construction ships with the square, which helps anyone laying out a first roof or a set of stair stringers.

Specs
– Size: 7 in
– Material: heavy-gauge die-cast aluminum, matte finish
– Markings: high-visibility black gradations
– Corners: CNC machined to 45 and 90 degrees
– Scales: degree scale 0 to 90, common rafter, hip and valley rafter
– Scribe notches: quarter-inch notches
– Heel: 7/8 in
– Included: 62-page Blue Book
– Made in: USA
– Weight: 8 oz
– Dimensions: 7.25 x 7.25 x 0.75 in

Empire e2994 True Blue Rafter Square, 7-Inch

Empire e2994 True Blue Rafter Square, 7-Inch

Empire e2994 True Blue Rafter Square, 7-Inch

Check price on Amazon

The Empire e2994 is the pick for anyone who has squinted at washed-out markings on a bright job site. Its True Blue high-visibility finish and laser-etched graduations stay readable in direct sun, and the laser etching will not wear off the way printed marks do. The heel is forty percent wider than a standard square, which gives the tool a steadier register against a board edge and more grip when guiding a saw.

The SCRIBE-GUIDE notch pattern marks rip lines at half-inch and quarter-inch increments, so the square doubles as a quick rip gauge for common lumber widths. The body is aluminum, light enough at 7 oz to ride in a pouch all day, and the laser-etched scales cover the same common and hip and valley rafter layout as the other 7-inch picks here. Empire is a division of Milwaukee Tool.

Specs
– Size: 7 in
– Material: aluminum
– Markings: True Blue laser-etched high-visibility graduations
– Heel: forty percent wider than standard
– Scribe notches: SCRIBE-GUIDE pattern at half-inch and quarter-inch increments
– Scales: common rafter, hip and valley rafter, degree scale
– Weight: 7 oz
– Dimensions: 8 x 8 x 1.13 in

Johnson 1959-0700 Magnetic Johnny Square, 7-Inch

Johnson 1959-0700 Magnetic Johnny Square, 7-Inch

Johnson 1959-0700 Magnetic Johnny Square, 7-Inch

Check price on Amazon

The Johnson 1959-0700 Magnetic Johnny Square is the pick for work on steel. Rare-earth magnets in the heel hold the square firmly to ferrous surfaces, so it stays put on steel studs, metal decking, and pipe while both hands are free to mark or cut. That magnetic grip is the feature that separates it from every other 7-inch square here, and it is the reason to choose this one if metal work fills the week.

Beyond the magnets, the Johnny Square is a full layout tool. The body is solid aluminum with laser-etched easy-read graduations, and the anti-glare finish keeps the numbers crisp in full sun. Continuous scribing grooves run from 1 inch through 5 and a half inches for rip marking, and the thick edge works as a saw guide. An instruction manual ships with the square.

Specs
– Size: 7 in
– Material: aluminum
– Heel: magnetic, holds to ferrous surfaces
– Markings: laser-etched easy-read graduations, anti-glare finish
– Scribe grooves: continuous, 1 in through 5 and a half in
– Edge: thick edge works as a saw guide
– Part number: 19590700
– Included: instruction manual
– Weight: not stated
– Dimensions: not stated

Swanson S0107 Big 12 Speed Square, 12-Inch

Swanson S0107 Big 12 Speed Square, 12-Inch

Swanson S0107 Big 12 Speed Square, 12-Inch

Check price on Amazon

The Swanson S0107 Big 12 is the same proven square scaled up for wide stock. At 12 inches on each side it reaches across wide boards, long layout lines, and roof components that a 7-inch square cannot span in one placement. For anyone who routinely frames with wide lumber or lays out long rafter runs, the extra five inches of reach turn two placements into one and keep long lines straight.

The Big 12 carries the same layout features as the classic 7-inch S0101: die-cast aluminum body, degree scale, common rafter and hip and valley rafter scales, scribe notches, and a 62-page Blue Book for rafter lengths and roof construction. The larger body also makes a steadier saw guide on wide panels, since the fence edge registers against more of the board.

Specs
– Size: 12 in
– Material: die-cast aluminum
– Markings: high-visibility gradations
– Scales: degree scale, common rafter, hip and valley rafter
– Scribe notches: quarter-inch notches
– Included: 62-page Blue Book
– Made in: USA
– Weight: not stated
– Dimensions: not stated

How to choose

Size comes first. A 7-inch square fits a tool pouch, rides on a belt all day, and handles dimensional lumber up to a 2 by 8 without a second placement. A 12-inch square reaches across wide boards and long layout lines, but it is heavier and bulkier to carry, so most framers own the 7-inch size first and add the 12-inch body when wide stock becomes routine.

Material and markings decide how long the square stays accurate and readable. Die-cast or extruded aluminum is the standard: it is light, it will not rust, and it holds a machined edge. Laser-etched or deeply cut markings outlast printed ones, and a matte or high-visibility finish keeps the numbers readable in direct sun. Check that the square is machined flat at 45 and 90 degrees, since a square that reads true is the whole point of the tool.

Look at the heel and the scribe notches next. A wide heel registers firmly against a board edge and gives a better grip for saw guiding. Scribe notches at quarter-inch increments mark rip lines without a tape, and a magnetic heel earns its keep on steel studs and metal decking. Finally, confirm the scales match the work: common and hip and valley rafter scales for roofing, a degree scale for angle work, and a guide book if rafter math is new to the buyer.

Who should skip

A speed square is a framing and roofing tool, and some workshops have little use for one. Fine furniture makers who work to tight tolerances with a combination square and a marking knife will find a rafter square too coarse for their layout, and the imperial scales on all five picks here suit inch-based lumber rather than metric-only workflows. Anyone building only small boxes or model work will find a 7-inch triangle oversized for the bench.

The 12-inch Big 12 is easy to overbuy. If the work is mostly trim, small framing, and repair jobs, the larger body adds bulk to the pouch without adding a single useful mark. Likewise, the magnetic Johnny Square only earns its premium over a plain square when steel surfaces are a regular part of the week. For everyone else, a plain 7-inch square does the same layout work.

FAQ

What size speed square should I buy first?

A 7-inch square is the right first buy for almost everyone. It fits a pouch, handles dimensional lumber up to a 2 by 8, and covers square marks, 45-degree marks, rafter layout, and saw guiding. Add a 12-inch square only when wide boards and long layout lines become routine.

Can a speed square guide a circular saw?

Yes. The thick heel registers against the edge of a board, and the straight edge of the square acts as a fence for the saw base on square and 45-degree cuts. Hold the square firmly against the board edge, keep the saw base flat against the square, and make the cut in one steady pass.

What is the diamond cutout on a Swanson square for?

The diamond cutout is Swanson’s mark of a genuine square, and it also serves as a layout aid. It sits at the pivot area of the square and helps position the tool for certain rafter and angle markings described in the Blue Book.

Do I need a 12-inch square if I already own a 7-inch one?

Only if the work regularly outgrows the smaller square. A 12-inch body spans wide boards and long layout lines in a single placement, which matters for roof framing and wide panel work. For trim, repair, and standard framing, the 7-inch square already covers the job.

Final verdict

The Swanson S0101 is the square to buy first, because it does every layout job a framer asks of it. The Empire e2994 is the better pick when readability in bright sun matters, and the Johnson magnetic Johnny Square is the one to own for steel work. The IRWIN 1794464 covers the same core jobs at the budget tier, and the Swanson Big 12 is the right second square once wide boards become routine. Any of the five will mark true lines for years; the choice comes down to size, readability, and whether a magnetic heel earns its keep.

L
Loa Power Tools Editorial Team
We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Speed Squares for Accurate Framing and RoofingCheck price on Amazon

Related guides

Browse all Product Guides guides →

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.