Key takeaways
- To use a drill press safely, clamp the workpiece so it cannot spin, set the speed to suit the bit and the material, wear eye protection.
What's inside
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
To use a drill press safely, clamp the workpiece so it cannot spin, set the speed to suit the bit and the material, wear eye protection, keep sleeves, hair and jewelry away from the spindle, and feed the bit with steady, moderate pressure. Most drill press injuries start the same way: a part held in a bare hand catches on the bit and whips around, so securing the work matters more than any other step.
This guide walks through the full sequence, from the checks you make before the switch goes on to the cleanup afterward. It is written for hobbyists, new shop owners and anyone who inherited a floor-standing or benchtop machine and wants a dependable routine. Shop habits do not change much from year to year, and the basics are the same in 2026 as they were decades ago. Your machine’s own manual always outranks general advice, so treat this as a framework to fill in with the specifics printed for your model.
Before You Start
- Read the manual for your exact machine, including the section on belt guards, speed ranges and maximum chuck capacity.
- Put on safety glasses or a face shield. Add hearing protection if you will be drilling metal or running the machine for long stretches.
- Remove rings, watches, bracelets and necklaces, roll up or button sleeves, tie back long hair, and skip gloves that could wrap around a spinning bit.
- Confirm the chuck key is out of the chuck and has a place to live that is not the table.
- Check that the guards and covers are closed and the table lock handle is tight.
- Clear the table and floor of scraps, cords and clutter so nothing snags and you have stable footing.
- Make sure the lighting lets you see the layout mark and the bit tip without leaning over the spindle.
Setting Up the Machine
Choose the Right Bit and Seat It Properly
Use a bit that is sharp, straight and designed for the material in front of you. Twist bits suit wood, plastic and metal in general, brad-point bits help in wood where the start point should not wander, and Forstner or spade bits make larger holes in wood. A dull or bent bit forces you to push harder, which invites grabbing and overheating. Insert the shank fully into the chuck, tighten it with the key in at least two of the three holes if your chuck has them, and then remove the key and put it down before anything else happens. Spin the chuck by hand to see that the bit runs true and does not wobble.
Match Speed to Bit Size and Material
A good rule is that larger bits and harder materials call for slower speeds, while small bits in softer materials can run faster. Wood generally tolerates higher speeds than steel, and large-diameter bits in any material should run slow because the outer edge travels much faster than the center. Most machines change speed by moving a belt between pulley steps, so unplug the machine before opening the guard. Your manual or a speed chart taped to the machine will list recommended ranges for the common bit sizes. If you see smoke, discolored bit tips or burning smells, the speed is probably too high or the bit is dull.
Set the Table Height and Depth Stop
Raise or lower the table so the bit tip sits only a short distance above the work at the top of its travel, which keeps your hands out of the long open space beside the spindle. For blind holes, set the depth stop and make a trial lowering with the power off to confirm the bit will stop where you want it. For through holes, place a scrap of wood under the workpiece so the bit exits into sacrificial material instead of the table or the vise jaws.
Securing the Workpiece
Never hold a part by hand while drilling. Even a small piece of thin sheet metal can grab the bit, spin up and cut fingers or throw the part. Pick a holding method that matches the shape of the work:
- A drill press vise bolted or clamped to the table for small, flat or round pieces.
- Toggle clamps or C-clamps for larger boards and plates, attached so the clamp does not interfere with the spindle.
- A fence or stop block clamped to the table when drilling repeated holes in the same position.
- V-blocks to cradle round stock so it cannot roll.
Mark the hole with a center punch when drilling metal. The small dimple gives the bit tip a place to start and cuts down on walking. Lower the bit gently to the mark with the power off, and make sure the work is positioned where you want it before you tighten everything down.
Drilling Step by Step
- Confirm the machine is plugged in only after the bit, speed and clamps are all set.
- Stand balanced with your free hand away from the table and the bit path.
- Start the motor and let it reach full speed before the bit touches the work.
- Lower the feed handle with even pressure. Let the bit cut instead of leaning on it.
- Back the bit out periodically on deeper holes to clear chips and let the bit cool. This is often called pecking.
- Ease off as the bit nears breakthrough, because that is the moment bits are most likely to grab.
- Raise the bit fully, wait for the spindle to stop, then release the clamps.
Common Hazards and What They Look Like
| Warning sign | Likely cause | What to do |
|---|---|---|
| Workpiece spins or lifts | Not clamped, or bit grabbing at breakthrough | Stop the machine, clamp the part, reduce feed pressure |
| Smoke or blue-tinted bit | Speed too high or bit dull | Slow down, sharpen or replace the bit, add cutting fluid for metal |
| Bit wanders at the start | No center punch, or worn bit | Punch the mark, start with a smaller pilot hole |
| Squealing or chatter | Wrong speed, loose belt, loose chuck | Power down and inspect belt, chuck and bit seating |
| Long ribbons of metal wrapping the bit | Continuous feed without clearing chips | Peck the bit, use a brush or hook, never clear chips by hand while running |
| Table moves under load | Lock handle loose | Re-tighten and re-check alignment |
Cleanup and Routine Care
Turn the machine off and wait for the spindle to stop completely before you brush away chips. Use a brush or a shop vacuum, not your bare hand, because metal swarf can be razor-sharp even when it looks harmless. Wipe the table and column, then lightly oil bare metal surfaces if your manual suggests it to prevent rust. Look over the belt, guard and power cord for wear whenever you change speeds, and store bits in an index or case so you reach for the correct size next time. Unplug the machine when you are changing parts, cleaning around the spindle or leaving the shop for an extended period.
If you are unsure about drilling a particular material, such as certain plastics, brittle stock or anything that produces fine dust, check the manufacturer guidance for that material and consider asking an experienced machinist or instructor to walk you through the first few cuts.
Related guides
- Corded Drills For Heavy Duty Use
- Mig Welders For Thin Sheet Metal
- How To Change A Circular Saw Blade
Frequently Asked Questions
Should I wear gloves at the drill press?
Generally no. Gloves can catch on a spinning bit and pull your hand in. Fitted work gloves are better kept for handling rough stock before and after drilling, with bare, clean hands near the running spindle.
How do I stop a bit from wandering at the start of a hole?
Mark the position with a center punch for metal or an awl for wood, start with a smaller pilot hole for large bits, and make sure the bit is sharp. Clamping the work firmly also keeps the layout mark where you put it.
What is the safest way to drill small or round parts?
Hold them in a drill press vise or V-block that is itself secured to the table. Small parts are the ones most likely to spin, so they deserve more clamping, not less.
Can I change speed while the machine is running?
On belt-driven machines, no. Switch the power off, unplug the machine, open the guard and move the belt to the right pulley step. Some variable-speed models adjust with a handwheel while running, but follow your manual for that process.
Related guides
Read next
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.
Write Your Review
No reviews yet. Be the first to share your experience!